| ID |
Date |
Author |
Category |
Subject |
Text |
 |
|
309
|
Mon Jan 25 13:03:22 2021 |
Dinko Ferencek | POS | POS configuration files created | The output POS configuration files has '_Bpix_'
instead of '_BPix_' in their names. The culprit
was identified to be the C3 cell in the 'POS' |
|
|
4
|
Tue Aug 6 16:06:45 2019 |
Matej Roguljic | Other | Vsh and ctrlreg for v4 chips | The recommended default value for Vsh is 8,
but the current version of pXar has it as
30. One should remember this when making |
|
|
8
|
Tue Sep 10 15:18:20 2019 |
Matej Roguljic | Other | Modules 1504, 1505, 1520 irradiation report | Modules 1504, 1505 and 1520 were taken to
Zagreb for irradiation on 13.08.19. The goal
was to check the v4 behavior after irradiation. |
|
|
10
|
Fri Sep 13 15:06:51 2019 |
Andrey Starodumov | Other | Modules 1504, 1505, 1520 irradiation report | It was discovered that these modules were
stored in Zagreb in the climatic lab where
T was about +22C. These modules have been |
|
|
12
|
Thu Sep 19 00:52:24 2019 |
Dinko Ferencek | Other | Modules 1504, 1505, 1520 irradiation report | [quote="Andrey Starodumov"]It was discovered
that these modules were stored in Zagreb
in the climatic lab where T was about +22C. |
|
|
99
|
Wed Mar 11 15:34:57 2020 |
Urs Langenegger | Other | M1586: issues with MOLEX? | Module M1586 had passed the full qualification
on 20/02/27. I had had to re-insert the cable
in the Molex connector for it to become programmable. |
|
|
100
|
Wed Mar 11 16:48:10 2020 |
Andrey Starodumov | Other | M1586: issues with MOLEX? | [quote="Urs Langenegger"]Module M1586 had
passed the full qualification on 20/02/27.
I had had to re-insert the cable in the Molex |
|
|
155
|
Sun Mar 29 18:14:59 2020 |
danek kotlinski | Other | Modules 1544 & 1563 in gelpack | The 2 bad modules:
M1544
M1563
|
|
|
175
|
Thu Apr 2 17:10:08 2020 |
Andrey Starodumov | Other | Cap glued to M1618 | M1618 has been tested (FT ) on March 23 without
a protection cap.
I have no idea how it's happened...
|
|
|
210
|
Tue Apr 14 16:54:31 2020 |
Andrey Starodumov | Other | M1633 cable disconnected | We do not have any more module holders.
M1633 was in "Module doctor" tray.
I took module off the holder and put it in |
|
|
237
|
Wed Apr 29 08:48:06 2020 |
Urs Langenegger | Other | M1539 | M1539 showed no readout. I tried, all without
success,
- reconnecting the cable to the adapter multiple |
|
|
258
|
Mon May 11 14:14:05 2020 |
danek kotlinski | Other | M1606 | On Friday I have tested M1606 at room temperature
in the red cold box.
Previously it was reported that trimming |
|
|
259
|
Mon May 11 14:40:16 2020 |
danek kotlinski | Other | M1582 | On Friday I have tested the module M1582 at
room temperature in the blue box.
The report in MoreWeb says that this module |
|
|
264
|
Wed May 13 17:57:45 2020 |
Andrey Starodumov | Other | L1_DATA backup | L1_DATA files are backed up to the LaCie disk |
|
|
275
|
Tue May 26 23:00:50 2020 |
Dinko Ferencek | Other | Problem with external disk filling up too quickly | The external hard disk (LaCie) used to back
up the L1 replacement data completely filled
up after transferring ~70 GB worth of data |
|
|
303
|
Fri Sep 18 15:45:21 2020 |
Andrey Starodumov | Other | M2211 and M2122 | I made a mistake and instead M2122 used ID
M2211 in the .ini file.
Hence now we do not have entry for M2122 |
|
|
307
|
Mon Jan 18 13:53:44 2021 |
Andrey Starodumov | Other | DTB tests | M2217
--->DTB 154 (one of the red cold box setup):
- flat cable (with HV):
|
|
|
301
|
Wed Sep 2 16:09:24 2020 |
Matej Roguljic | Modules for P | M1595 switch with M1558 | Module 1595 was foreseen to go on the inner
ladder 5, position -2 (negative two). During
the pre-installation test, we saw it had |
|
|
62
|
Tue Feb 4 19:35:38 2020 |
Dinko Ferencek | Module transfer | 7 modules prepared for transfer to ETH: 1536, 1537, 1538, 1540, 1541, 1542, 1543 | The following modules have been prepared today
for transport to ETH for x-ray qualification:
1536, 1537, 1538, 1540, 1541, 1542, 1543
|
|
|
66
|
Wed Feb 5 16:18:30 2020 |
Dinko Ferencek | Module transfer | Module location tracking added to the assembly spreadsheet | To keep track of the module location, two
columns were added to the module assembly
spreadsheet [URL=https://docs.google.com/spreadsheets/d/12m2ESCLPH5AyWuuYV4KV1c5O_NEy7uP5PQKzVsdr3wQ/edit?usp=sharing]https://docs.google.com/spreadsheets/d/12m2ESCLPH5AyWuuYV4KV1c5O_NEy7uP5PQKzVsdr3wQ/edit?usp=sharing[/URL] |
|