| ID |
Date |
Author |
Category |
Subject |
Text |
 |
|
108
|
Mon Mar 16 10:05:23 2020 |
Matej Roguljic | Software | PhQualification change | Urs made a change in pXar, in the PhOptimization
algorithm. One of the changes is in the testParameters.dat
where vcalhigh is set to 100 instead of 255. |
|
|
107
|
Sat Mar 14 17:08:14 2020 |
Matej Roguljic | Full test | Fulltests on 2020/03/13 |
Modules tested:
M1591 C (gain at -20)
|
|
|
105
|
Thu Mar 12 17:21:59 2020 |
Matej Roguljic | Full test | Fulltests on 2020/03/12 | Modules tested:
M1557 C (trim bits at -20)
M1558 C (gain at -20)
|
|
|
104
|
Thu Mar 12 12:19:43 2020 |
Matej Roguljic | HDI test | 5 HDI tests on 12.3. | I tested 5 HDIs on 12.3. 1030,1029,1040,1039
and 1038. 1039 failed all the electrical
tests. All the others passed the tests. HDI |
|
|
103
|
Wed Mar 11 17:59:48 2020 |
Andrey Starodumov | Re-grading | Regrading C M1542: due to Noise | Follow the instruction from M1591 regrading
log:
"To correct the Summary page one needs to |
|
|
102
|
Wed Mar 11 17:22:57 2020 |
Matej Roguljic | HDI test | 8 HDI tests on 11.3. | I tested 8 HDIs today: 5029,5030,5031,6034,6036,6035,1031
and 1032
All of them tested fine. |
|
|
101
|
Wed Mar 11 17:12:05 2020 |
Matej Roguljic | HDI test | HDI testing procedure change | There is an additional test that will be used
from 11.03. on all HDIs. It involves measuring
the voltage between ground and the HV pin |
|
|
100
|
Wed Mar 11 16:48:10 2020 |
Andrey Starodumov | Other | M1586: issues with MOLEX? | [quote="Urs Langenegger"]Module M1586 had
passed the full qualification on 20/02/27.
I had had to re-insert the cable in the Molex |
|
|
99
|
Wed Mar 11 15:34:57 2020 |
Urs Langenegger | Other | M1586: issues with MOLEX? | Module M1586 had passed the full qualification
on 20/02/27. I had had to re-insert the cable
in the Molex connector for it to become programmable. |
|
|
98
|
Mon Mar 9 16:16:48 2020 |
Andrey Starodumov | HDI test | HDIs: 3001, 3002, 3003, 3004 and 4033 | Today I tested 5 HDIs: 3001, 3002, 3003, 3004
and 4033
Results:
|
|
|
97
|
Wed Mar 4 16:00:05 2020 |
Andrey Starodumov | Re-grading | Regrading C M1591: due to Noise | [quote="Andrey Starodumov"]It has been realized
by Urs that VCal to electron conversion used
by MoreWeb is still 50e/VCal.
|
|
|
96
|
Wed Mar 4 11:32:42 2020 |
danek kotlinski | Full test | change the target trim threshodl to vcal=50 | After some discussion we decided to change
the target trimming threshold from vcal 40
to 50.
|
|
|
95
|
Tue Mar 3 14:05:13 2020 |
Andrey Starodumov | Re-grading | Regrading C modules: due to Noise | It has been realized by Urs that VCal to electron
conversion used by MoreWeb is still 50e/VCal.
While recent calibration done by Maren with |
|
|
94
|
Mon Mar 2 17:39:36 2020 |
Urs Langenegger | Full test | Fulltests on 2020/03/02 | Modules tested:
M1595 C
M1596 B
|
|
|
93
|
Fri Feb 28 17:33:16 2020 |
Urs Langenegger | Full test | Fulltests on 2020/02/28 | M1589 B
M1590 C (gain issues?)
M1591 C (noise issues?)
|
|
|
92
|
Thu Feb 27 10:14:09 2020 |
danek kotlinski | Module transfer | M1562 to DESY | M1562 was not qualified during a full test
since the test did not complete.
Looking at the module I see that roc 2 has |
|
|
91
|
Thu Feb 27 09:47:51 2020 |
Urs Langenegger | Full test | Fulltest on 2020/02/26 | On Wednesday, 2020/02/26 the following modules
went through the full qualification procedure:
|
|
|
90
|
Wed Feb 26 10:34:55 2020 |
Urs Langenegger | Full test | Fulltest after Peltier replacement | On 2020/02/25, after SIlvan had replaced the
Peltiers, I did a fulltest. Here the summary:
|
|
|
89
|
Tue Feb 25 17:11:18 2020 |
Urs Langenegger | Module assembly | Modules glued and tested Feb 24/25 | Modules glued and tested Feb 24/25
The letters after the module name indicate |
|
|
88
|
Mon Feb 24 14:01:29 2020 |
Urs Langenegger | Module assembly | Cap gluing in W8 | In week 8 the following modules were glued
and tested:
|
|